TMDSEMU200-U XDS200 USB Debug Probe - TI | Mouser
J-Link Adapters | SEGGER - The Embedded Experts This adapter allows the use of J-Link with ARM7/9/11 targets using this 14-pin 0.1" mating JTAG connector defined by ARM. The 14-pin connector, though defined by ARM as an alternative to the 20-pin connector is not widely used on modern eval boards. More Info 1BitSquared - 20Pin JTAG Adapter Board Kit This is an adapter for the standard 10pin 0.05" pitch ARM Cortex JTAG connector to the legacy 20pin 0.1" pitch ARM JTAG connector. The JTAG adapter board kit is a useful accessory for connecting your Black Magic Probe JTAG/SWD adapter to older ARM evaluation/development boards as well as easily connecting 0.1" headers, ARM-JTAG-20-10 - olimex.com Plug-in adapter for ARM-USB-OCD, ARM-USB-OCD-H, ARM-USB-TINY, ARM-USB-TINY-H which allows borads with small 10-pin 0.05 inch step connector to be programmed/debugged. Follows the official ARM JTAG layout
Product Selector Which Board is most suitable for A 10-pin to 20-pin JTAG Adapter designed to convert between the ARM mini-JTAG connector (10-pin) and the standard ARM JTAG connector (20-pin) Usage. The picture to the right shows how the JTAG adapter Template:FLYSWATTER2 BEAGLEBOARD CONNECT - eLinux.org 1.1 Set the EMU pins on the JTAG Adapter Board. 1.2 Connect the JTAG Adapter Board to the Flyswatter2. 1.3 Connect the 14-pin Ribbon Cable to the JTAG Adapter Board. 1.4 Connect the RS-232 adapter board to the Flyswatter2. 1.5 Connect the 10-pin cable to the Flyswatter2. 1.6 Connect the other end of the 10-pin cable to the Beagleboard. 20 pin ARM/14 pin TI emulator to 20 pin ARM Adapter 20 pin ARM/14 pin TI emulator to 20 pin ARM . Emulator Header - 20 ARM or 14 TI; Target Header - 20 ARM; Recommended for - Third Party ARM tools and XDS510/XDS560 Emulators (DM644x target boards) Adapters with Voltage translation supported provides between 3.3V emulator interfaces and JTAG targets that require down to 1.8V interfaces. JTAG Adapters - software-dl.ti.com
The board's 20-pin female connector is designed to plug directly into the matching male connector of your ARM JTAG unit (in place of the normally used 20-pin cable). Note: This item is not a programmer/debugger itself. It is merely an adapter for owners of an existing programmer/debugger. ARM20cTI20 – cTI 20-pin JTAG Adapter Board The ARM20cTI20 JTAG adapter board converts the Flyswatter2’s ARM 20-pin JTAG interface into a compact TI (cTI) 20-pin JTAG interface for Texas Instruments target boards. This JTAG adapter board enables the Flyswatter2 to interface with the following target boards: BeagleBone Black; BeagleBone; Any target board with a cTI 20-pin JTAG interface J-Link Adapters | SEGGER - The Embedded Experts This adapter allows the use of J-Link with ARM7/9/11 targets using this 14-pin 0.1" mating JTAG connector defined by ARM. The 14-pin connector, though defined by ARM as an alternative to the 20-pin connector is not widely used on modern eval boards. More Info 1BitSquared - 20Pin JTAG Adapter Board Kit This is an adapter for the standard 10pin 0.05" pitch ARM Cortex JTAG connector to the legacy 20pin 0.1" pitch ARM JTAG connector. The JTAG adapter board kit is a useful accessory for connecting your Black Magic Probe JTAG/SWD adapter to older ARM evaluation/development boards as well as easily connecting 0.1" headers,
DSTREAM family – Arm Developer Second-generation Arm debug probe, enabling maximum debug visibility into Arm processors, with 2.4 Gbps parallel trace over 4 pins, streams trace data directly to host machine, system autodetection with Development Studio. Supports a range of target connectors including JTAG, MICTOR, and CoreSight. Olimex ARM-JTAG-20-10 ARM Micro JTAG Adapter: Amazon.in: Office I now design all my ARM boards using the 1.27mm 10-pin JTAG mini connector. It saves a lot of space in the board's footprint. Then I use this Olimex adapter to down-convert from the 2.54mm 20-pin JTAG connector of my Atmel SAM-ICE to the 10-pin connector in my board (the 10-pin shrouded connector I used on my board is DigiKey's 1175-1629-ND). The ARM20TI14 JTAG adapter board converts the Flyswatter2’s ARM 20-pin JTAG interface into a 14-pin JTAG interface for Texas Instruments target boards. Buffered TI14-pin/ARM20-pin JTAG to CTI20-pin JTAG Header Adapter $149.00
The ARM20cTI20 JTAG adapter board converts the Flyswatter2’s ARM 20-pin JTAG interface into a compact TI (cTI) 20-pin JTAG interface for Texas Instruments target boards. This JTAG adapter board enables the Flyswatter2 to interface with the following target boards: BeagleBone Black; BeagleBone; Any target board with a cTI 20-pin JTAG interface
Blackhawk JTAG Pin Converters
